Closed type

Features of the "CLASSIK" system for roller blinds: 1. The smallest on the market, aesthetic aluminum cassette measuring 35*64mm allows you to open windows wider with the curtain installed and limits the penetration of light to a lesser extent than in similar competitive systems. 2. The width of the product is 12 mm wider than the fabric. 3. The cassette is attached to the glazing bead or sash (frame) of the window using four self-tapping screws, and the guides are glued with double-sided tape 9mm wide. 4. Guide width 30mm. 5. The width of the bottom beam is 9mm. 6. Aluminum shaft with a diameter of 18 mm. 7. To avoid shaft deflection, with a width of more than 1400 mm, a reinforcing profile is inserted into the shaft. 8. Installed on windows with rectangular or rounded beads with a bead depth of at least 12 mm. On windows with shaped glazing beads or with glazing beads of shallower depth, roller blinds of the Classic system are NOT installed due to the technological features of this system. Features of the "PROFIL" system for roller blinds: 1. The cassette is attached to the window sash (frame) using an adaptive snap strip, which is very firmly glued with double-sided tape. The guides are glued to the glazing bead or sash (frame) of the window with 9 mm wide tape. 2. An innovative adaptive snap strip connecting the curtain cassette to the window sash (frame) allows it to be removed from the window without the need to peel off or cut double-sided tape. 3. The latch strip is applied in a spot manner (every 500 mm). 4. The use of a snap strip in 106 mm pieces minimizes the elasticity of the cassette mounted on an uneven window profile, which eliminates the phenomenon of the roller blind peeling off from the window sash (this occurs with wide windows). 5. The PROFIL system cassette has a blockade of the lower beam along its entire length, which prevents the beam from being pulled into the cassette. 6. Dimensions of the cassette - 50*70mm, guide - 20*13*23mm. 7. Aluminum shaft with a diameter of 18 mm. 8. To avoid shaft deflection, with a width of more than 1400 mm, a reinforcing profile is inserted into the shaft. Features of the "MIX" system for roller blinds: A compact and aesthetic cassette measuring 36*49 mm allows you to open windows wider with the curtain installed. 1. The Vegas Mix system cassette can be installed both at the top and bottom of the window, while maintaining all the functions of a roller blind. 2. The fishing line and spring mechanism in the Vegas Mix system allow you to freely raise and lower both the cassette and the lower beam, as well as fix them in any position, adjusting the degree of window shading. 3. The upper and lower fastenings are attached to the window sash (frame) or glazing bead using self-tapping screws. 4. The upper and lower ends of the fishing line are completely masked by mounting elements, which make it possible to easily tension the fishing line and adjust it at any time without additional complex operations. 5. The dimensions of the upper fastenings are 18*22mm, the lower fastenings are 10*15mm. 6. Aluminum shaft with a diameter of 13 mm. 7. ATTENTION!!! Using this roller blind system allows you to close the lower part of the window while leaving its upper part open, and vice versa. Features of the "SK-40" system for roller blinds: 1. At the client's request, the "SK-40" system can be equipped with long or short curtain rods, with or without curtain rod extensions, which allow you to increase the distance between the wall and the roller blind. 2. Such curtain rods are used when installing roller blinds of the “SK-40” system on a wall or ceiling, if their plane does not allow the installation of clips with a box. 3. Cornice extension 85 mm - small bracket, 125 mm - large bracket, 195 mm - large bracket with extension. 4. Box extension - 90 mm, box height - 89 mm. 5. Silent, soft operation of the mechanism. 6. Maximum system dimensions: 7. Maximum system width 2900 mm. 8. Maximum system height 4300 mm. 9. The maximum area of roller blinds is 6.0 square meters. 10. The width of the finished product is 37 mm greater than the width of the fabric (22 mm on the control side and 15 mm on the other side). 11. An aluminum shaft with a diameter of 40mm is used. 12. The “SK-40” system is equipped with a stopper and a chain holder. 13. Direct or reverse winding is possible.